TiO2/MXene-Assisted LDI-MS for Urine Metabolic Profiling in Urinary Disease

Cancer remains an intractable medical problem. Rapid diagnosis and identification of cancer are critical to differentiate it from nonmalignant diseases. High-throughput biofluid metabolic analysis has potential for cancer diagnosis. Nevertheless, the present metabolite analysis method does not meet the demand for high-throughput screening of diseases. Herein, a high-throughput, cost-effective, and noninvasive urine metabolic profiling method based on TiO₂/MXene-assisted laser desorption/ionization mass spectrometry (LDI-MS) is presented for the efficient screening of bladder cancer (BC) and nonmalignant urinary disease. Combined with machine learning, TiO₂/MXene-assisted LDI-MS enables high diagnostic accuracy (96.8%) for the classification of patient groups (including 47 BC and 46 ureteral calculus (UC) patients) from healthy controls (113 cases). In addition, BC patients can also be identified from noncancerous UC individuals with an accuracy of 88.3% in the independent test cohort. Furthermore, metabolite variations between BC and UC individuals are investigated based on relative quantification, and related pathways are also discussed. These results suggest that this method, based on urine metabolic patterns, provides a potential tool for rapidly distinguishing urinary diseases and it may pave the way for precision medicine.     

喷射成形Al-Zn-Mg-Cu合金挤压态的组织和力学性能

研究了利用喷射成形辅以挤压制备Al-5.72Zn-2.36Mg-1.66Cu合金后优化的组织结构特征和力学性能。结果表明,合金基体组织均匀细化,晶粒形貌趋于圆整,平均晶粒大小达到10 μm左右。当合金的冷却条件通过快速凝固技术改变时,会产生不同程度的固溶强化效果和第二相弥散强化效果,从而改善了合金的整体性能。合金的屈服强度和抗拉强度分别平均提高了20%左右,且伸长率也略有提高。     

[成形过程仿真优化与集成计算材料工程]限定加热管布局的快速热循环注塑成形模具电加热系统优化

针对管道布局、最大允许能耗给定条件下快速热循环注塑成形（RHCM）注塑模具型腔表面快速均匀加热的问题，提出以单根加热棒热流密度为设计变量，以模具型腔表面升温效率和温度分布均匀性为目标，结合有限元模拟、响应面设计以及多目标粒子群优化技术来优化RHCM模具电加热系统。与优化前相比，加热系统优化后，模具型腔表面最大温差降低63.4%，加热系统总能耗降低9%。对比了不同注塑成形工艺条件下成形的平板塑件表面质量，结果表明，相对传统注塑成形（CIM）工艺，RHCM工艺将制品表面粗糙度Ra从320 nm降低到118 nm，并有效抑制了制品表面熔接痕、缩痕等缺陷；发现制品表面粗糙度与型腔表面对应点温度成负相关，说明优化后的型腔表面温度分布更有利于提升制品表面质量。     

Pure CuBi2O4 Photoelectrodes with Increased Stability by Rapid Thermal Processing of Bi2O3/CuO Grown by Pulsed Laser Deposition

A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi₂O₄ photoelectrodes by sequentially depositing Bi₂O₃ and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi₂O₄. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi₂O₄ photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi₂O₄ photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.     

Refinement of primary carbides in AISI DC 53 cold work tool steel by thin section copper permanent mould casting and water atomization

In this study, as alternative methods to conventional production methods involving thin section copper permanent mould casting (fast solidification) and water atomization (rapid solidification) of AISI DC 53 cold work tool steel have been investigated. Thin slabs obtained by copper mould casting was homogenized at 1150 °C for one hour and then hot rolling was be applied. After hot rolling, conventional heat treatment have been applied to thin slabs. The same heat treatment procedure have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. In order to investigate also the effect of rapid solidification on AISI DC 53 tool steel, steel powder was produced by water atomization technique. Experiments have revealed that thin steel slabs in permanent copper mould and rapidly solidified tool steel powder by water atomization have a more refined primary M₇C₃ carbides than commercially available steel.     

Compilation of Modern Technologies To Map Genome-Wide Cytosine Modifications in DNA

Over the past few decades, various DNA modification detection methods have been developed; many of the high-resolution methods are based on bisulfite treatment, which leads to DNA degradation, to a degree. Thus, novel bisulfite-free approaches have been developed in recent years and shown to be useful for epigenome analysis in otherwise difficult-to-handle, but important, DNA samples, such as hmC-seal and hmC-CATCH. Herein, an overview of advances in the development of epigenome sequencing methods for these important DNA modifications is provided.     

冶金矿物和产品水分测定问题探讨

水分测定是冶金行业中矿产原料和产品分析的重要内容,主要包括交货水分、湿存水、化合水等测定类别。尽管水分测定方法本身相对简单,但其涉及到矿物原料、产品结算交割以及其他化学分析的校正计算,属于重要的基础性测定方法。各类矿物、产品几乎都有相应水分测定的国家标准、行业标准,部分还是从国外ISO标准体系中采标而来。文章系统介绍并比较各类矿物原料、产品中交货水分、明水、湿存水、化合水等类别的测定方法。由于ISO标准体系中湿存水含义和国内标准体系湿存水含义有较大差异,其测定操作和用途也有不同,使用空气平衡样品和密封原始样品将会得到数据差异较大的湿存水数据,两种湿存水含义需要明确区分。湿存水对化学称样量、灼减量、化合水的测定有影响,需要用湿存水进行水分校正,才能得到更精确的结果。